1. <tbody id="y5rbp"></tbody>
    <tbody id="y5rbp"></tbody>

    <tbody id="y5rbp"></tbody>
    <th id="y5rbp"><table id="y5rbp"><thead id="y5rbp"></thead></table></th>
    <tbody id="y5rbp"></tbody>
    <small id="y5rbp"><listing id="y5rbp"><thead id="y5rbp"></thead></listing></small>

  • <tbody id="y5rbp"></tbody>

  • <code id="y5rbp"></code>

      1. <tbody id="y5rbp"></tbody>

        <bdo id="y5rbp"></bdo>
        <mark id="y5rbp"><tt id="y5rbp"></tt></mark>
        當前位置: 首頁 - 新聞資訊 - 公司動態 -

        濟南通風管道安裝都包括哪些步驟?

        來源:http://www.boursomarket.com 日期:2021-07-10 發布人:jntfgd

        首先,通風管道的安裝,首先注意到其實也在通風管總成,在管道的時間比較短,在很大程度上可以也是一個在地面上組裝,緊隨其后的是管道很長一段時間,在很大程度上,其實也可以直接根據安裝地點的狀況,直接在地面單位組裝。
          First of all, the installation of ventilation pipes, first of all, notice that in fact it is also in the ventilation pipe assembly, in a relatively short period of time in the pipeline, to a large extent, it can also be a ground assembly, followed by pipelines for a long period of time, to a large extent, in fact, it can also be directly assembled in the ground unit according to the status of the installation site.
          風管裝配時,風管的和水平應盡可能調整,在很大程度上可以直接避免風管的變形或上下波動和左右擺動。此外,應該注意的是,每個部分的風道不應超過10m。裝配時應將墊片壓平,法蘭螺栓擰緊均勻,使螺母帽面朝同一方向。
          When the duct is assembled, the center and level of the duct should be adjusted as far as possible. To a large extent, the deformation or fluctuation of the duct can be avoided directly. In addition, it should be noted that each part of the duct should not exceed 10m. When assembling, gaskets should be flattened, flange bolts should be tightened evenly, so that the nut face faces in the same direction.
          此外,通風管道,管道之前到位,很大程度上其實也應該注意對水的直接檢查所有支架與海拔度,然后,注意應該是直接檢查的程度強烈的腿,管的地方也可以采用直接和傳播者,這兩個方法。
          In addition, ventilation pipes, pipes in place before, to a large extent, should also pay attention to the direct inspection of water support and altitude, and then, pay attention to the degree of direct inspection should be strong legs, pipes can also use direct and disseminator, these two methods.
          那么,對于通風管道截面相對較小,且其位置相對較低,在很大程度上,其實可以直接采用人工就位的方法,只需要直接設置簡單的腳手架也可以。
          Then, for the ventilation duct section is relatively small, and its location is relatively low, to a large extent, in fact, the method of manual positioning can be used directly, as long as a simple scaffold can be directly set up.
          后告訴大家,通風管道上的風管截面在其管道截面上較大較長,其實就是在其很大程度上可以直接采用滑輪、倒角鏈或大繩等方法。為了方便在通風管道上安裝風管,應注意風管應直接懸掛在腳手架上。
          Finally, let us know that the cross section of the air duct in the ventilation duct is larger and longer than that in the duct section. In fact, to a large extent, pulleys, chains or ropes can be directly used. In order to facilitate the installation of air ducts on ventilation pipes, it should be noted that air ducts should be directly suspended on scaffolding.
        上一篇:安裝通風管道前的6個準備工作
        下一篇:分享通風管保溫工藝的經驗
        >

        推薦產品

        • 廚房排煙
        • 廚房排煙
        • 軸流風機
        • 不銹鋼制品

        本站圖片均由網站所有方提供,部分圖片來源于網絡,如有任何疑問請及時與我們聯系,未經溝通本站不承擔相關法律責任!

        网易财经